Mercedes Sprinter 3.0L 3" DPF Delete Parts Kit (2010-2025)

Introduction

Free your Sprinter from restrictive emissions equipment with the Mercedes Sprinter 3.0L 3-inch DPF Delete Exhaust, designed for 2010–2025 Mercedes-Benz and Freightliner Sprinter 2500/3500 vans equipped with the 3.0L V6 diesel engine.

This complete Sprinter DPF delete kit removes the Diesel Particulate Filter (DPF), catalytic converters and related exhaust restrictions to improve exhaust flow, reliability and drivability for race-use applications.

The system supports early W906 exhaust designs (2010–2018) and revised W907 / W910 exhaust configurations (2019–2025). Mercedes updated the exhaust and turbo direct pipe in late 2018, so it is important to confirm which exhaust version your Sprinter uses before ordering.

This Sprinter dpf delete kit is available in T-304 or T-409 stainless steel. Both versions use the same design, fitment and components. The material choice affects corrosion resistance and cost only, not performance or fitment.

Vehicle Fitment

Important: Mercedes changed the exhaust design in late 2018. Always verify whether the vehicle uses the early or revised exhaust configuration before ordering.

Features

• Complete 3-inch DPF delete exhaust system for Mercedes Sprinter 3.0L V6 diesel
• Fits 2010–2018 (early) and 2019–2025 (W907 / W910) exhaust designs
• Available in T-304 or T-409 stainless steel
• 3" OD, 16-gauge mandrel-bent tubing
• Factory-style mounting brackets to reduce added turbo stress
• Integrated flex pipe to handle heat and engine movement
• Reducer adapter included for stock exhaust connection
• All clamps and hardware included
  

Benefits

• Removes restrictive DPF and catalytic converters
• Improves exhaust flow on tuned Sprinter 3.0L engines
• Supports better drivability under load
• Helps reduce exhaust backpressure
• Reduces long-term stress on the turbocharger
• Built for durability in off-road and work environments

Technical Specifications

• Material Options: T-304 or T-409 stainless steel
• Tube Diameter: 3-inch OD
• Tubing Thickness: 16-gauge
• System Type: DPF delete / straight-pipe exhaust

What’s Included

• DPF delete downpipe for Sprinter 3.0L
• 3" mid-pipe section
• Reducer adapter (3" mid-pipe to stock exhaust)
• 3" exhaust strap clamps

Installation & Notes

• Estimated install time: 3–4 hours
• Install time depends on tools and experience
• Vehicle lift is strongly recommended
• All clamps and adapters are included

Important Notes

• Disconnect SCR controller, NOx sensors, AdBlue injector, and DPF pressure/EGT sensors before tuning
• If the van has an active DEF countdown, idle mode, or emissions-related fault, Mercedes-specific diagnostic tools must be used to clear codes before tuning
• Failure to reset fault codes can cause limp mode or improper operation

Please Note: The vehicle must be properly tuned before or immediately after deleting emissions components.

Frequently Asked Questions (FAQ)

Q1: What is the difference between T-304 and T-409 stainless steel?
A1: Both versions have the same fitment and design. T-304 offers higher corrosion resistance, while T-409 is a cost-effective option commonly used in exhaust systems.

Q2: Does this exhaust kit fit all 2018 Sprinter 3.0L vans?
A2: Yes, but you must confirm whether the van uses the early or revised exhaust design, as both were used during that model year.

Q3: Is tuning required?
A3: Yes. Race tuning is required for proper operation after DPF removal.

Please Note

For off-road use only. Buyer is responsible for fitment, legal compliance and use.